Ce produit n'est plus disponible et a été remplacé par: LOGGERLINK. Certains accessoires, pièces de rechange ou des services peuvent être encore disponibles.
| Services disponibles |
|---|
Aperçu
Current Version: 2.33
Le logiciel de PConnectCE permet les communications entre une centrale d'acquisition de données Campbell Scientific et un PDA PocketPC ou Windows Mobile. PConnectCE vous permet d'aller sur le terrain seulement avec votre PDA et des câbles au lieu d'avoir un ordinateur portable pour communiquer avec votre centrale de mesure et collecter vos données.
Lire la suiteImages
Description technique
PConnectCE can be used to collect data from the datalogger, and transfer the data to an office PC. Collected data are transferred to the PC during the ActiveSync® process. This process also synchronizes program files between the handheld and the PC.
Functions supported by PConnectCE includes the capability to:
- Create unique station fi les for each datalogger
- Collect data from the datalogger
- Display real-time datalogger measurements. Measurements are updated every two seconds.
- Set datalogger flags, ports, and clock
- Access the datalogger terminal mode
- Transfer datalogger programs between the datalogger and handheld
- Display Final Storage data in tabular or comma-separated format
- Communicate using a direct serial connection, RF401-series Spread Spectrum Radio, or Bluetooth
- Graph one element from any array
- Communicate at baud rates of 38,400 bps (CR800, CR850, CR1000, CR23X, CR3000) and 9,600 bps (all other dataloggers)
DCE/DTE Information
PConnectCE ships with connectors and cables that assume the PDA acts as a DCE device (data communications equipment), with the 9-pin cable terminating in a female connection. Some PDAs act like a DTE device (data terminal equipment) and the 9-pin cable terminates in a male connection. If this is the case, for communication via the CS I/O port, you will most likely use an SC32B (purchased separately) in place of the PDA-to-CSI/O connector that ships with the software. To communicate via the datalogger's RS-232 port, the PDA's serial cable can be plugged in directly to the datalogger's RS-232 port (or a standard serial cable can be used if extended cable length is required). There may be exceptions, however, to this general rule. If you have questions about the RS-232 capabilities of your handheld device, check with the device manufacturer.
Compatibilité
Veuillez noter : Ce qui suit montre des informations de compatibilité générales. Ce n'est pas une liste complète de tous les produits compatibles.
Centrale de mesure
| Produits | Compatibilité | Note |
|---|---|---|
| CR1000 (obsolète) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
| CR200X (obsolète) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
| CR216X (obsolète) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
| CR3000 (obsolète) | The CR3000 requires PConnectCE version 2.1 or higher. | |
| CR5000 (obsolète) | ||
| CR800 (obsolète) | The CR800 and CR850 require PConnectCE version 2.2 or higher. | |
| CR850 (obsolète) | The CR800 and CR850 require PConnectCE version 2.2 or higher. | |
| CR9000X (obsolète) |
Informations de compatibilité supplémentaires
Data Logger Considerations
Data Logger Interfacing
- PDA-to-CS I/O connector or PDA-to-RS232 cable.
--OR--
- SC-IRDA Infrared Interface connects to the CS I/O port (not compatible w/CR200(X)-series)
PDA Requirements
- Operating system: Microsoft Pocket PC or Windows Mobile®
- Must be capable of serial communication
- If using the SC-IRDA, the PDA must have an IRDA port and an IR chip set compatible with the SC-IRDA.
- For Bluetooth communication, the handheld must be Bluetooth enabled.
- Pocket PCs or Mobile Handhelds Tested by Campbell Scientific
Communication Requirements
PDA Connection for Serial Communication
PDA-to-serial cable or cradle (one end of the cable/cradle must terminate in a 9-pin serial connector) is required. The cable/cradle connects to the PDA-to-CS I/O connector or PDA-to-RS232 cable via the 9-pin serial connector. This cable/cradle may be included with the PDA, or it may need to be purchased as a separate accessory from the PDA manufacturer or a third party supplier.
Bluetooth Communication
Third-party Bluetooth serial adapter is required. The interface and/or cables that are used to connect the adapter to the data logger will vary, depending upon whether the device acts like a DTE (computer) device or DCE (PDA) device. In some instances, this is evident by the pin-out of the adapter, but not always. A general rule is if the adapter has a 9-pin female connector, then the adapter is connected to the data logger using the PDA-to-CS I/O connector for the CS I/O port or the PDA-to-RS232 cable for the RS-232 port. If the adapter has a 9-pin male connector, then the adapter is connected to the data logger using an SC32B for the CS I/O port or it can be connected directly to the RS-232 port.
Software
- A compatible version of Microsoft ActiveSync installed on the PC
- One copy of PConnectCE software per handheld
Spécifications
| Current Version | Version 2.33 began shipping in May 2008. |
| Software Requirements |
|
| PDA Operating System | Microsoft Pocket PC or Windows Mobile |
| Operating Temperature | -25° to +50°C |
| CE Compliance | CE Compliant |
| PDA to RS-232 Cable Length | 38.0 cm (15.0 in.) |
| PDA to RS-232 Cable Weight | 75 g (2.6 oz) |
| PDA to CS I/O Connector Dimensions | 2.3 x 4.1 x 7.6 cm (0.9 x 1.6 x 3.0 in.) |
| PDA to CS I/O Connector Weight | 41 g (1.6 oz) |
Documents à télécharger
Téléchargements
PCONNECTCE Patch v.2.33 (1.65 MB) 22-05-2008
Upgrade PConnectCE 2.0, 2.1 or 2.2 to 2.33.
PConnectCE 2.0, 2.1 or 2.2 must be installed on your machine.
FAQ
Nombre de FAQ au sujet de(s) PCONNECTCE: 11
Développer toutRéduire tout
-
PConnectCE version 2.x provides support for:
- Our PakBus dataloggers
- Infrared (IR) communication
- Bluetooth communication
- COM ports greater than 2
-
On the PDA, select Start | Programs | PConnectCE.
-
No. PConnectCE is compatible with direct serial communications (COM1─COM8), Infrared, Bluetooth, and point-to-multipoint RF401 radio communications in a Transparent RF network. For more information, refer to the “Connecting Your Pocket PC Handheld to the Datalogger” section of the instruction manual.
-
PConnectCE is installed on the PC. When the hot sync process is used with the Windows Mobile device, PConnectCE is transferred to the device. For more information, refer to the instruction manual.
-
Yes. The Archer-PCon package includes PConnectCE software. The PConnectCE manual includes instructions for installing the software.
-
Yes. The value of an input location or Public variable can be changed from the Measurements tab.
-
Use PConnect software for Palm devices or PConnectCE software for Windows Mobile devices.